鋼管自動切斷倒角機床設計（QZ11-16×220）

畢業設計（論文）中文摘要

鋼管自動切斷倒角機床（QZ11-16x220）是帶式輸送機托輥鋼管切斷、兩端倒角一次自動完成的專用設備，該機床自動化程度高、加工精度高，如送料，定位，夾緊，倒角，切斷依次進行，一次就能滿足鋼管的加工精度，不需要輔助加工，并且安裝調試方便。該設備采用的是硬質合金刀（YT5系列刀具），其硬度，耐磨性，耐熱性都很好，切削速度遠比高速鋼快得多。液壓系統中使用了雙聯泵供油，保證了運動速度，切斷采用進口調速出口被壓裝置，使切斷速度可調、工作穩定?？刂葡到y(tǒng)采用可編程控制器(PLC)為中心，限位采用無觸點開關，動作程序準確可靠。鋼管加工過程，由“自動送料—送料到位—夾緊—夾緊到位—進刀—進刀到位—自動落料—放松退刀—退刀到位—自動送料”循環進行，大大提高工作效率，并能適應大批量生產加工。

關鍵詞  切斷倒角    刀具     液壓系統      控制系統

畢業設計（論文）外文摘要

Title  The chamfer machine tool for cutting steel pipeautomatically

        
Abstract
The chamfer machine tool for cutting steel pipe automatically.（QZ11-16x220）。The chamfer machine tool provides various working procedures for cutting the steel pipe automatically such as feeding, positioning, clamping, chamfer and cutting. The automaticity is good. It can satisfy the machining precision of the steel pipe and not need assistant machine. The installation and debugging of the equipment is convenient. This equipment is equipped with carbide tool （YT5 series） which is better than high-speed steel knife. The hardness, wear resistance and thermostability of the tool are perfect. Two pumps supply the oil to satisfy the parameters in the hydraulic system. The control system use PLC as the center. The limited switch is no touch. The course of working as follow:  automatic feed-feed in position-clamp-clamp in position-sumping-sumping in position-automatic blanking. The cycle can improve the work efficiency and work with a batch of workpiece.

Keywords  chamfer cutting   tool   hydraulic system    control system

目      次

1.引言                     ………………………………………………5
2.機床的簡介               ………………………………………………6
3.機床主軸箱元件選擇及校核     …………………………………………7
4.傳動系統及機床潤滑      ………………………………………………24
5.送料機構的選擇          ………………………………………………24
  5.1 送料機構的確定      ………………………………………………24  
  5.2 送料小車的確定      ………………………………………………24
5.2.1 確定傳動形式    ………………………………………………24
5.2.2 小車電機的選擇  ………………………………………………24
5.2.3 皮帶的選擇      ………………………………………………25
5.2.4 蝸輪蝸桿的選擇于校核    ……………………………………27
5.2.5 車輪的布置      ………………………………………………28
  5.3 小車軌道的確定      ………………………………………………29
6.定尺機構                ………………………………………………29
  6.1 機構簡介            ………………………………………………29
  6.2 動作順序            ………………………………………………29
  6.3 工作原理            ………………………………………………29
7.機床電器系統            ………………………………………………30
8.機床的使用              ………………………………………………31
9.簡單故障的處理          ………………………………………………32
10.附圖                   ………………………………………………33
11.結論                   ………………………………………………43
12.參考文獻               ………………………………………………44
13.致謝                   ………………………………………………45