道路交通燈的設計.doc
約35頁DOC格式手機打開展開
道路交通燈的設計,頁數35字數11653摘 要紅綠燈控制是智能交通系統的一個重要部分,本文給出了一個用單片機控制的簡易交通紅綠燈自動控制系統。該系統適用于十字路口,并對放行和禁行時間進行倒計時顯示(秒),且放行和放行時間可以根據需要進行調整。關鍵詞:紅綠燈,單片機 ,交通信號燈 ,自動控制abstractthe cont...


內容介紹
此文檔由會員 劉陽 發布
道路交通燈的設計
頁數35 字數11653
摘 要
紅綠燈控制是智能交通系統的一個重要部分,本文給出了一個用單片機控制的簡易交通紅綠燈自動控制系統。該系統適用于十字路口,并對放行和禁行時間進行倒計時顯示(秒),且放行和放行時間可以根據需要進行調整。
關鍵詞:紅綠燈,單片機 ,交通信號燈 ,自動控制
Abstract
The control of red-green lamp is a very important part of Intelligent Transportation System.In this paper,an intelligent red-green lamp automatic control system in Simple of the Single Chip MicroComputer(SCMC) control is introduced. The system is applicable to the intersections of the single main highway,and to let go time proceed to pour to account hour manifestation(s).
Key Words: red-green lamp
Single Chip MicroComputer(SCMC)
transportation signal lamp
automatic control
目 錄
前 言---------------------------------------------4
第1章 道路交通燈的總體設計-----------------------5
1.1道路交通燈系統的總體設計方案-------------------------5
1.2 道路交通燈系統的硬件設計方案------------------------6
1.3 道路交通燈系統的軟件設計方案-----------------------7
第2章 硬件設計---------------------------------9
2.1 系統分析-------------------------------------------9
2.2 主要內容及技術指標---------------------------------10
2.3 關鍵技術-------------------------------------------10
2.4 單片機硬件系統設計原則------------------------------10
2.5 單片機的應用----------------------------------------11
2.6時鐘電路的設計----------------------------------------12
2.7 復位電路的設計---------------------------------------12
2.8 按鍵設計---------------------------------------------14
2.9 顯示電路的設計---------------------------------------15
第3章 軟件設計-----------------------------------17
3.1按鍵提示系統-----------------------------------------18
3.2時間調整模塊------------------------------------------18
3.3顯示程序設計-----------------------------------------20
第4章 調試及故障排除----------------------------23
4.1硬件調試-------------------------------------------23
4.2 軟件調試------------------------------------------24
第5章 結論--------------------------------------25
參考文獻---------------------------------------------26
致 謝------------------------------------------------27
附 錄------------------------------------------------28
參考文獻
[1].李群芳、肖看 《單片機原理、接口及應用---嵌入式系統技術基礎》[M]. 清華大學出版社2006
[2].靳達《單片機應用系統開發實例導航》[M]. 人民郵電出版社 2003
[3].沈德全《MCS51系列單片機接口電路與應用程序?qū)嵗穂M]. 北航出版社2001
[4].韓克、柳秀山 《電子技能與EDA技術》[M].暨南大學出版社 2005
[5].閻石 《數字電子技術基礎》[M]. 高等教育出版社 1998
頁數35 字數11653
摘 要
紅綠燈控制是智能交通系統的一個重要部分,本文給出了一個用單片機控制的簡易交通紅綠燈自動控制系統。該系統適用于十字路口,并對放行和禁行時間進行倒計時顯示(秒),且放行和放行時間可以根據需要進行調整。
關鍵詞:紅綠燈,單片機 ,交通信號燈 ,自動控制
Abstract
The control of red-green lamp is a very important part of Intelligent Transportation System.In this paper,an intelligent red-green lamp automatic control system in Simple of the Single Chip MicroComputer(SCMC) control is introduced. The system is applicable to the intersections of the single main highway,and to let go time proceed to pour to account hour manifestation(s).
Key Words: red-green lamp
Single Chip MicroComputer(SCMC)
transportation signal lamp
automatic control
目 錄
前 言---------------------------------------------4
第1章 道路交通燈的總體設計-----------------------5
1.1道路交通燈系統的總體設計方案-------------------------5
1.2 道路交通燈系統的硬件設計方案------------------------6
1.3 道路交通燈系統的軟件設計方案-----------------------7
第2章 硬件設計---------------------------------9
2.1 系統分析-------------------------------------------9
2.2 主要內容及技術指標---------------------------------10
2.3 關鍵技術-------------------------------------------10
2.4 單片機硬件系統設計原則------------------------------10
2.5 單片機的應用----------------------------------------11
2.6時鐘電路的設計----------------------------------------12
2.7 復位電路的設計---------------------------------------12
2.8 按鍵設計---------------------------------------------14
2.9 顯示電路的設計---------------------------------------15
第3章 軟件設計-----------------------------------17
3.1按鍵提示系統-----------------------------------------18
3.2時間調整模塊------------------------------------------18
3.3顯示程序設計-----------------------------------------20
第4章 調試及故障排除----------------------------23
4.1硬件調試-------------------------------------------23
4.2 軟件調試------------------------------------------24
第5章 結論--------------------------------------25
參考文獻---------------------------------------------26
致 謝------------------------------------------------27
附 錄------------------------------------------------28
參考文獻
[1].李群芳、肖看 《單片機原理、接口及應用---嵌入式系統技術基礎》[M]. 清華大學出版社2006
[2].靳達《單片機應用系統開發實例導航》[M]. 人民郵電出版社 2003
[3].沈德全《MCS51系列單片機接口電路與應用程序?qū)嵗穂M]. 北航出版社2001
[4].韓克、柳秀山 《電子技能與EDA技術》[M].暨南大學出版社 2005
[5].閻石 《數字電子技術基礎》[M]. 高等教育出版社 1998