彈性位移要求：系統參數的不確定性與地型數據的隨機性-----外文翻譯.doc
約12頁DOC格式手機打開展開
彈性位移要求：系統參數的不確定性與地型數據的隨機性-----外文翻譯,摘要：本文的主要內容是：量 化成比例的源于(1)廣泛承認記錄的變化性，(2)內在隨機性的系統參數，彈性的總位移比率模式主導結構相當名義上決定橫向強度。隨機系統參數處理均為：系統正常獨立考慮橫向屈服強度和系統粘性阻尼比。 monte carlo模擬技術是一套選自從20規模地震數據中總結出來被廣泛用來取代sdof系統的數據...
內容介紹
此文檔由會員 wanli1988go 發布
摘要：本文的主要內容是：量 化成比例的源于(1)廣泛承認記錄的變化性，(2)內在隨機性的系統參數，彈性的總位移比率模式主導結構相當名義上決定橫向強度。隨機系統參數處理均為：系統正常獨立考慮橫向屈服強度和系統粘性阻尼比。 Monte Carlo模擬技術是一套選自從20規模地震數據中總結出來被廣泛用來取代SDOF系統的數據模擬系統。各向主要傾向的措施是，變化性的分散系數，被認為是這位移的數率。被普遍認為，分散的數率在位移比率的準則下被認為隨機性的系統參數要遠小于人為記錄數據時的多變性。估計這種被報道的復表面重力波的分解的以后很有可能實施于性能抗震設計新興概率和評價方法。據還表明，在所產生的分散位移比率的可變性參數低于本身內在分散系統參數只有在極少數的情況或短時間內發生。
1 介紹
H. Rahamia, A. Kavehb,_, Y. Gholipoura
a Engineering Optimization Research Group, University of Tehran, Tehran, Iran
b Centre for Excellence for Fundamental Studies in Structural Engineering, Iran Universityof Science and Technology, Narmak, Tehran-16, Iran
Received 25 April 2007; received in revised form 1 January 2008; accepted 15 January 2008
Available online 10 March 2008
1. Introduction
For size/geometry optimization of structures with fixed topology, it becomes necessary to optimize structural crosssections and geometry simultaneously. For such optimization,usually large numbers of design variables will be encountered consisting of cross-sectional areas and nodal coordinates, thus resulting in design spaces with large dimensions. Selecting the cross-sectional areas from a list of profiles leads to a discrete design space, and due to the constraints on member stresses, buckling stresses, and nodal displacements, the possibility of being trapped in a local optimum increases.Goldberg is one of the pioneers in developing the Genetic algorithm [1]. Early papers on structural optimization using GA are due to Goldberg and Samtani [2], Jenkins [3], Adeli and Cheng [4] and Rajeev and Krishnamoorthy [5]. Many others
have published papers improving the results and increasing the speed of GA in the last decade.In the process of optimizing the geometry (shape) of a structure by the
1 介紹
H. Rahamia, A. Kavehb,_, Y. Gholipoura
a Engineering Optimization Research Group, University of Tehran, Tehran, Iran
b Centre for Excellence for Fundamental Studies in Structural Engineering, Iran Universityof Science and Technology, Narmak, Tehran-16, Iran
Received 25 April 2007; received in revised form 1 January 2008; accepted 15 January 2008
Available online 10 March 2008
1. Introduction
For size/geometry optimization of structures with fixed topology, it becomes necessary to optimize structural crosssections and geometry simultaneously. For such optimization,usually large numbers of design variables will be encountered consisting of cross-sectional areas and nodal coordinates, thus resulting in design spaces with large dimensions. Selecting the cross-sectional areas from a list of profiles leads to a discrete design space, and due to the constraints on member stresses, buckling stresses, and nodal displacements, the possibility of being trapped in a local optimum increases.Goldberg is one of the pioneers in developing the Genetic algorithm [1]. Early papers on structural optimization using GA are due to Goldberg and Samtani [2], Jenkins [3], Adeli and Cheng [4] and Rajeev and Krishnamoorthy [5]. Many others
have published papers improving the results and increasing the speed of GA in the last decade.In the process of optimizing the geometry (shape) of a structure by the
