畢業設計 大型管材相貫線切割機設計
論文說明書共27頁，字?jǐn)?shù)總計：11271
資料簡介：
A0-Z軸方向工作滑臺裝配圖.dwg
A0-割炬支架裝配圖.dwg
A1-相貫線切割機總體布局圖.dwg
A1-硬件連接線路圖.dwg
畢業設計說明書：大型管材相貫線切割機設計.doc
封面.doc
目錄
目錄 1
中文摘要 2
Abstract 2
第 1 章 緒論 3
第 2 章 數學模型及工藝分析 4
2.1鋼管典型相貫線數學模型的建立 4
2.2 割炬運動分析 5
2.3 焊接坡口工藝分析 6
2.4 割炬的徑向補償 6
第3章 設備總體方案及布局 7
3.1 機床總體方案 7
3.2 切割機傳動系統的簡要說明 7
3.3 功能和技術參數分析 8
第4章 機械系統設計 10
4.1 Z軸工作滑臺的設計 10
4.2調整絲杠的設計 17
4.3 齒輪齒數的確定與較核 18
4.4 支架的設計 18
第 5 章 控制系統設計 20
5.1系統方案設計 20
5.2 控制系統的選用 21
5.3 數控裝置的部件結構和安裝 21
5.4.控制系統的硬件設計 22
5.5 圖形交互人機界面 23
總 結 25
鳴 謝 26
參考文獻 27


中文摘要
本設計以相貫線數學參數模型的基礎, 分析切割機的割炬的軌跡運動, 將切割運動分解為割炬回轉、割炬平移、割炬擺角和割炬徑向補償四軸聯動,對鋼管相貫焊接坡口數控切割運動進行研究,并最終完成相貫線切割機的設計.該切割機采用數控原理進行軌跡控制，采用火焰切割方式工作.設計共分四部分:相貫線數學參數模型的建立,切割機總體方案設計,機械結構設計和控制系統設計.
關 鍵 詞:大型管材;相貫線;焊接坡口;數控火焰切割
Abstract
Based on the mathematical model of intersecting line and the analysis of the track of cutting torch, the design studies NC cutting movement for welding groove of pipe intersecting and finishes the design of pipe intersecting line cutting device . The cutting movement was divided into four axis relative motions of cutting torch, i. e. rotate round the pipe, shift along pipe, swing and compensate along radial direction. The device uses NC principle for intersecting line track control, the cutting method is flame-cutting. And the design contains four sections: the establishment of mathematical model of intersecting line, the design of the whole scheme, the design of mechanical structure and the design of NC control system.
Keywords: Large-scale pipe; Intersecting line; Welding groove; NC flame-cutting