畢業設計 往復螺桿式注塑機注射系統設計
論文說明書共29頁，字?jǐn)?shù)總計：10066
資料簡介：
A0-往復螺桿式注射裝置.dwg
A4-噴 嘴.dwg
A3-料筒頭.dwg
A2-料筒.dwg
A3-螺桿.dwg
A3-小齒輪.dwg
A3-大齒輪.dwg
A3-高速軸.dwg
A1-擋板.dwg
A1-料斗座.dwg
開題報告.doc
立題表.doc
任務書.doc
說明書.doc
目 錄

摘要 I
Abstract II
1 緒論 1
1.1研究的目的及意義 1
1.2研究內容 1
1.3注塑機的現狀 1
1.4需要解決的問題 2
2 總體方案設計 4
2.1柱塞式注射裝置 4
2.2螺桿預塑式注射裝置 5
2.3往復螺桿式注射裝置 5
2.4方案的選定 6
3主要零部件設計 7
3.1塑化裝置的設計 7
3.1.1螺桿設計 7
3.1.2料筒的設計 10
3.2傳動裝置的設計 11
3.2.1單級圓柱齒輪減速器的設計 11
3.2.2軸的設計計算 17
3.3注射裝置的設計 19
3.3.1噴嘴的設計 19
3.3.2螺桿最大行程計算 20
3.3.3液壓油缸的直徑計算 20
3.3.4注射力計算 20
4結論 22
參考文獻 23
致謝 24
往復螺桿式注塑機注射系統設計
摘要
本文根據給定的設計參數介紹了一種往復螺桿式注射系統的設計，所設計的注射系統包括傳動裝置、塑化裝置、注射裝置三大部分。傳動裝置采用了單級齒輪減速器和三相異步電動機滿足設計要求，塑化裝置采用了三級變徑螺桿與料筒結合完成對坯料的塑化，注射裝置采用了單向液壓缸與往復螺桿結合，由液壓缸活塞推動螺桿完成注射過程并在下一循環的塑化過程中自動完成螺桿的退回。所設計的裝置具有結構簡單、性能可靠、制造容易的特點。
關鍵詞：注塑機；注射系統；往復螺桿式
Design of The Injection System of Reciprocating Screw Type Plastic Injection Machine
Abstract
The design according to the given design parameters describes a reciprocating screw injection system design, the design of the injection system includes gear, plastics unit, injection unit of three parts. Transmission using a single-stage gear reducer and the three-phase induction motor to meet the design requirements, plasticizing device uses three adjustable screw and barrel combined with the completion of the blank plastics, injection device using one-way hydraulic cylinder and reciprocating Screw combination of hydraulic cylinder piston driven by the injection screw to complete the process and in the course of the next cycle of the plasticizing screw back automatically.The design of the device has a simple structure, reliable performance, easy to manufacture characteristics.
Keywords: injection molding machine; injection system; reciprocating screw