攻絲組合機床畢業設計
1.1萬字 29頁




中文摘要

本文是關于雙面臥式攻絲機床設計的說明。此機床要求：在兩個面同時進行自動攻絲。
本文主要內容包括設計的必要性分析；通過對設計的機床的功能分解與功能合成，以及對方案的設計從而提出新的加工方案。通過對定位方式的選擇和對工件工藝性的分析，以及對零件工序圖、加工示意圖、機床聯系尺寸圖和功率計算卡這“三卡一圖”的分析，提出對組合機床的總體設計方案。文中對組合機床的通用部件及專用部件的選擇都做了較為詳細的說明。由于要實現自動化，所以對液壓傳動系統和單片機的電氣控制系統的設計顯得尤為重要，本文也對此做了闡明，并編寫了程序。另外，本文還對設計做了小結。


關鍵詞 組合機床，攻絲，單片機。




Abstract

This text is concerning two-lyings offend the silk combination machine bed design of say. The design request of this machine bed is: proceed at the same time in two the auto offend the silk.
The main contents in this text includes the necessity analysis of the design; The function that pass the machine to design to bed resolves to synthesize with function, and the design of the other party case from but put forward to process the project newly. Pass to the choiceof the fixed method with to work an analysis for craft analysis, and to spare parts work preface diagram, processing sketch map, machine bed contact size diagram with power calculation stucking “three figures and one card”, put forword to the total design project of the combination machine bed. The text inside all did to the in general use parts of the combination bed and the choice of the appropriation parts than for expatiation. Because of realizing automation, so press to spread to move the system to the liquid to control with the electricity of SCM the design of the system seems to be particularly for importance, this text also makes to clarify to this, writing the procedure. Moreover, this text returns to this time designed to make the sub-footing.


Key phrase Combination machine bed, offend the silk,SCM.




目 錄

1 緒論 1
2 設計任務書 2
2.1 產品用途和使用范圍 2
2.2 關于機床的主要加工功能和系統組成的建議 2
2.3 關于總體布局的建議 3
2.4 主要技術指標和相關重要參數 4
2.5 主要工作原理 4
2.6 國內外的現狀和發展趨勢 4
2.7 國內外同類產品對比 6
2.8 跟題目有關的專利情況 6
2.9 關于采用新技術、新結構、新材料、新工藝的建議 8
2.10 擬采用的技術路線 8
3 組合機床的總體設計 9
3.1 組合機床的配置形式 9
3.2 機床加工示意圖 12
3.3 機床的聯系尺寸 12
4 組合機床通用部件及其選用 14
4.1 攻絲靠模裝置和攻絲卡頭 14
4.2 攻絲裝置及攻絲靠模頭 15
4.3 主軸箱的設計 16
5 進給機構的設計 20
6 電氣部分設計 21
6.1 整個機床的動作順序 21
6.2 電器原理圖 21
總 結 24
致 謝 25
參考文獻 26
附錄1 28
附錄2 30




參考文獻

1 胡乾斌、李光斌、李玲、甘錫英. 單片微型計算機原理與應用. 華中理工大學出版社
2 張毅剛、彭喜元、姜守達、喬立巖. 新編MSC-51單片機應用設計. 哈爾濱工業大學出版社