[外文翻譯]在線轉動的單片機監控系統工具的設計/ The design of a single-chip tool monitoring
system for on-line turning operation
內包含中文翻譯和英文原文，內容完善，建議閱覽下載。

①中文頁數 3

中文字?jǐn)?shù) 3636

②英文頁數 6

英文字?jǐn)?shù) 13013

③ 摘要

監控系統的工具狀態在一個FMS系統中起重要作用。通過改變將要或剛剛出現問題的產品，就可將缺陷產品引起的損失大大降低，因而產品質量和其可靠性被改進。為了達到這樣的目的，在這篇文章里討論在生產的過程期間為檢測工具破損而使用一臺單片機微機監控系統的在線工具條件。一般來說，基于PC的監控體制在大多數調查研究工作里被使用。這種監控體制的主要缺點是花費問題。為了降低費用，監控系統的工具由8051單片機的微處理器建造，設計也將在這篇文章內描述。8051的監控系統工具應用應變儀測量削減力，根據力學特性，監控系統工具能容易使用，由于它的工具破損算法再現切割工具的破損。實驗結果顯示在監控板上。低成本的8051控制工具能成功識別在3 種連續的產品內出現的工具破損。

Tool condition monitoring systems play an important role in a FMS system. By changing the worn tool before or just at the time it fails, the loss caused by defect product can be reduced greatly and thus product quality and reliability is improved. To achieve this, an on-line tool condition monitoring system using a single chip microcomputer for detecting tool breakage during cutting process is discussed in this paper. Conventionally, PC-based monitoring systems are used in most research works. The major shortcoming of PC-based monitoring systems is the incurred cost. To reduce costs, the tool condition monitoring system was built with an Intel 8051 single-chip microprocessor and the design is described in this paper. The 8051 tool monitoring system uses a strain gauge for measuring cutting force; according to the force feature, the tool monitoring system can easily recognize the breakage of the cutting tool with its tool breakage algorithm. The experimental results show that the low-cost 8051 tool monitoring board can detect tool breakage in three successive products successfully.


④關鍵字 產品破損/ Tool breakage;