液壓挖掘機工作裝置斗桿鋼結構有限元分析（本科畢業論文設計）.doc
約22頁DOC格式手機打開展開
液壓挖掘機工作裝置斗桿鋼結構有限元分析（本科畢業論文設計）,摘 要本設計主要對兩種典型工況下液壓挖掘機反鏟裝置斗桿鋼結構的受力進行了有限元分析。首先，計算出兩種工況位置下斗桿所受的外力，以此作為有限元分析的外載荷。然后采用pro/e軟件對斗桿鋼結構進行三維建模，并導入到ansys軟件中進行有限元分析。最后根據靜強度分析結果，對兩種工況進行比較，再分別找出兩種工況下受力斗桿的最大...
內容介紹
此文檔由會員 genmail 發布
摘 要
本設計主要對兩種典型工況下液壓挖掘機反鏟裝置斗桿鋼結構的受力進行了有限元分析。首先，計算出兩種工況位置下斗桿所受的外力，以此作為有限元分析的外載荷。然后采用PRO/E軟件對斗桿鋼結構進行三維建模，并導入到ANSYS軟件中進行有限元分析。最后根據靜強度分析結果，對兩種工況進行比較，再分別找出兩種工況下受力斗桿的最大應力位置，并對現行設計提出改進措施。
為了有利于分析，文中對斗桿鋼結構得模型采取了一些簡化措施。針對斗桿結構的復雜程度，選用四面體單元及殼單元對模型進行網絡劃分。對鉸銷間接觸載荷的處理時，假設載荷在X—Y平面180°范圍內按余弦分布，軸向均勻分布，以使其受力盡量符合實際。整個分析取得了良好得效果。
關鍵詞：液壓挖掘機，有限元分析，斗桿，ANSYS
ABSTRACT
In this paper,author mostly andlysed the stress of backhoe shovel device of hydraulic excavator under two kinds of typical condition with finite element method. First of all,figured out the external forces of bucket arm under the amphi-condition,and took this forces as the external loads of finite element analysis.Then built up the 3D moldof bucket arm with software PRO/E Finally,according to the analytic result of bucket arm’s static steength,compared the result under amphi-condition and found out the maximum steess position of bucket arm under amphi-condition respectively,and author brought out the improvement advice of product.
Author adopted some measures to simplify the bucket arm so that in favor of the finite element analysis.Because of the complexfity level of the structural of bucket arm,arthor took tetrahedral element and shell element to mesh the mold. In order to make the force as soon as possible accord with reality,when deal with contact load between the pin and the hole,author assumed the loads sperad by cosine within 180°of the x – y plane and rectangular distribution towards axial direction. Towards axial direction. Whole analyses procured a satisfying effect.
Keywords: Hydraulic Wxcavator,Finite Element Analysis,Bucket Arm,ANSYS
本設計主要對兩種典型工況下液壓挖掘機反鏟裝置斗桿鋼結構的受力進行了有限元分析。首先，計算出兩種工況位置下斗桿所受的外力，以此作為有限元分析的外載荷。然后采用PRO/E軟件對斗桿鋼結構進行三維建模，并導入到ANSYS軟件中進行有限元分析。最后根據靜強度分析結果，對兩種工況進行比較，再分別找出兩種工況下受力斗桿的最大應力位置，并對現行設計提出改進措施。
為了有利于分析，文中對斗桿鋼結構得模型采取了一些簡化措施。針對斗桿結構的復雜程度，選用四面體單元及殼單元對模型進行網絡劃分。對鉸銷間接觸載荷的處理時，假設載荷在X—Y平面180°范圍內按余弦分布，軸向均勻分布，以使其受力盡量符合實際。整個分析取得了良好得效果。
關鍵詞：液壓挖掘機，有限元分析，斗桿，ANSYS
ABSTRACT
In this paper,author mostly andlysed the stress of backhoe shovel device of hydraulic excavator under two kinds of typical condition with finite element method. First of all,figured out the external forces of bucket arm under the amphi-condition,and took this forces as the external loads of finite element analysis.Then built up the 3D moldof bucket arm with software PRO/E Finally,according to the analytic result of bucket arm’s static steength,compared the result under amphi-condition and found out the maximum steess position of bucket arm under amphi-condition respectively,and author brought out the improvement advice of product.
Author adopted some measures to simplify the bucket arm so that in favor of the finite element analysis.Because of the complexfity level of the structural of bucket arm,arthor took tetrahedral element and shell element to mesh the mold. In order to make the force as soon as possible accord with reality,when deal with contact load between the pin and the hole,author assumed the loads sperad by cosine within 180°of the x – y plane and rectangular distribution towards axial direction. Towards axial direction. Whole analyses procured a satisfying effect.
Keywords: Hydraulic Wxcavator,Finite Element Analysis,Bucket Arm,ANSYS
