畢業設計 CA6140方刀架工藝工裝設計（含2套夾具設計）
論文說明書共54頁，字?jǐn)?shù)總計：21657
資料簡介：
A0-鉆模板.dwg
A0-銑床夾具裝配圖.dwg
A1-鉆床夾具體.dwg
A1-鉆床夾具體裝配圖.dwg
A2-方刀架零件圖.dwg
A3-下墊板.dwg
A3-支座.dwg
A3-支撐板.dwg
A3-方刀架毛坯圖.dwg
A3-缸頭.dwg
A3-缸筒.dwg
A4-堵.dwg
A4-卡環.dwg
A4-絲桿.dwg
A4-拉桿.dwg
A4-活塞桿.dwg
A4-活塞.dwg
A4-杠桿.dwg
A4-缸尾.dwg
A4-定位銷.dwg
A4-定位套.dwg
A4-定位板.dwg
A4-長定位套.dwg
工序卡.dwg
過程卡1.dwg
過程卡10.dwg
過程卡9.dwg
過程卡8.dwg
過程卡7.dwg
過程卡6.dwg
過程卡5.dwg
過程卡4.dwg
過程卡3.dwg
過程卡2.dwg
開題報告.doc
摘要.doc
畢業論文：CA6140方刀架工藝工裝設計.doc
引言.doc
任務書.doc
摘 要
本次畢業設計是圍繞著CA6140機床方刀架的工藝工裝來展開的。內容主要包括以下幾個方面：設計零件的加工工藝（包括切削用量工時等計算）設計兩套專用夾具，對其中一套進行拆畫。作出一萬八千字的說明書。
方刀架的主要功用就是通過裝在刀架上的其它零件夾緊刀具，換刀時，在手柄轉動下，帶動方刀架回轉，以達到換刀的目的。
因?yàn)楣ぜ儆诖笈可a(chǎn)，宜采用專用夾緊裝置。所以為了適應生產需要，采用組合鉆床，設計專用的鉆模板，在回轉工作臺上進行多工位加工。
機床夾具的確定是一次十分重要的設計程序，方案的設計優劣往往直接決定夾具設計的可行性。所以，方案的確定需經充分的研究和討論來確定最佳方案。

由于 液壓傳動具有許多優點，如結構緊湊，體積小，重量輕，反應快，承載能力大；較易實現無級調速，調速比大；運動平穩；易于實現自動化；并能實現較復雜的自動化工作循環；具有自潤滑能力；磨損小，壽命長；液壓元件易于實現通用化、標準化，便于大批量生產。所以，本次所設計的夾緊方式就采用液壓壓緊。

關鍵詞：CA6140機床方刀架；液壓夾緊；工藝工裝設計


Abstract
This graduate design is around the square knife in bed in machine in CA6140 craft work packs to launch of.The contents includes primarily below a few aspects:Designing the spare parts processes the craft( include to slice 削 dosage man-hour etc. calculation) designs two sets of appropriations tongs, as to it's inside a set of proceedings dismantles the painting.Make a manual for 18,000th words.
The square knife an other spare parts for of main effect is passing packing on the knife clips the tight knife has, changing the knife, the in hand handle turns to move the bottom, arousing the square knife a purpose for turning round, then attaining changing the knife.
Because the work piece belongs to the large quantity measures production, the proper adoption appropriation clips the tight device.So produce the demand for the sake of the orientation, adoption combination drill the bed, design to drill the template appropriatively, at turn round the work on the stage proceed many the work processes.
It is design good and bad that machine bed tongs really settle that once very important design procedure that possibility, the project usually decides directly the tongs design.So, the project really settles to need through the sufficient research with discussion to certain the best project.

Because the liquid presses to spread to move to have many advantages, such as construction tightly packed, the physical volume is small, the weight is light, responding quick, load the ability is big;Than realizes to have no easily the class adjust soon, adjust to compare soon big;The sport is steady;Apt to realize automation;Combining can realize complicated automation work circulation;Have from the lubrication ability;Wear away small, the life span is long;The liquid presses a piece apts to realize in general use turn, standardizing, the easy to large quantity measures production.So, this designs of clip the tight way and then adopt the liquid press.

Key phrase:The square knife in bed in machine in CA6140; liquid presses to clip tight,;the craft work packs the design
目 錄

1 CA6140方刀架加工工藝 1
1.1 零件的分析 1
1.1.1零件的作用 1
1.1.2零件的工藝分析 1
1.2 毛坯的確定 2
1.2.1毛坯加工方法的確定 2
1.2.2毛坯尺寸及加工總余量的確定 2
1.2.3 毛坯的重量計算 2
1.3 工藝規程設計 2
1.3.1 定位基準的選擇說明 3
1.3.2不同工藝路線的分析比較 3
1.4選擇機床設備及工藝裝備 5
1.5確定機械加工余量，工序尺寸及其公差 6
1.6填寫工藝卡片和機械加工工序卡片 6
1.7確定切削用量及基本工時 6
2 機床夾具設計 14
2．1機床夾具概念 14
2．1．1機床夾具概念 14
2．1．2工件的安裝 14
2．1．3機床夾具的功用 14
2．1．4機床夾具的組成 15
2．2夾具設計的基本要求 15
2．3夾具設計方法和步驟 15
2．3．1研究原始資料，明確設計任務 15
2．3．2夾具結構方案的設計 15
2．4夾具總圖的繪制 17
3 液壓系統的設計 18
3．1液壓傳動系統的特點 18
3．2明確設計要求 18
3．3結構及工作概述 18
3．4液壓系統主要性能參數的確定 19
3．5工作原理及概述 19
3．6夾具的工作概述 20
3．7系統油缸的結構設計概述 21
3.7.1、液壓缸主要參數的選定： 21
3.8.裝配油缸的技術要求 28
3.9使用操作、維護管理說明 29
3.9.1液壓操作中工作液的管理 29
3.9.2運行的準備 29
3.9.3拆卸與重新裝配 ..